| ALASKA |
|
2006 UPC with Alaska Amendments
Length: 1 day
Description: Specific for the State of Alaska, this comprehensive course, based on the 2006 Uniform Plumbing Code provides a complete overview of the Alaska requirements including: Water System Sizing, Drain, Waste and Vent System Design, Gas System Design and Sizing, Cross Connection, Materials, Water Heater Installation, Venting, Combustion Air Requirements and Fixtures. |
|
CALIFORNIA |
|
2007 California Plumbing Code Essentials
Length: 1 or 2 days
Description: Based on the 2006 Uniform Plumbing Code with California Amendments, this 1 or 2 day seminar provides a full overview of the California requirements covering: Sizing of Drainage Systems, Cleanouts, Slope & Change of Direction of Drainage Flow, Use of Joints, Drainage Fixture units, Installation and Sizing of Building Sewers, Sumps & Sewage Ejectors, Indirect Waste Piping, Chemical Waste, Steam and Hot Water Drainage, Condensers and Sumps, Vent Sizing and Termination, Island Venting, Combination Waste and Vent and Wet Vents. |
|
2007 California Mechanical Code Essentials
Length: 1 or 2 days
Description: Based on the 2006 Uniform Mechanical Code with California Amendments, this 1 or 2 day seminar provides a full overview of the California requirements covering: Combustion Air Openings & Sizing Calculations, Sources of Combustion Air, Ducts and Dampers, Prohibited Sources, Vent Installation and Construction Requirements, Sizing Gravity, Induced & Forced Draft Systems, Multiple Appliance Venting, Chimneys and Vents, Mechanical Draft Systems, Return and Outside Air: Area Requirements, Prohibited Sources, Limitations, Vented Decorative Appliances, Room Heaters, Overhead Radiant Heaters, Incinerators, Direct Gas/Fired, Make Up Air Heaters and Individual Heaters, Clearances & Access. |
|
MAINE |
|
Maine Internal Plumbing Code
Length: 1 or 2 days
Description: 1 and 2 day Specific for the State of Maine, this course covers the 2000 Uniform Plumbing Code including all the Maine amendments. Topics reviewed and discussed include: General Administration, plumbing fixtures and fixture fittings, prohibited fixtures, special fixtures and specialties, installations for the handicapped, water supply and distribution, atmospheric vacuum breaker, heat exchangers, tempering valves, sanitary drainage, ferrules and bushings, size of drainage piping, cleanouts, indirect wastes, pressure drain connections, vents, traps and interceptors, storm drainage, and mandatory referenced standards. |
|
MINNESOTA |
|
Minnesota Mechanical and Fuel Gas Code
Length: 1 day
Description: Specific for the State of Minnesota, this seminar is based on the International Mechanical Code including the Minnesota amendments. Topics reviewed and discussed are; General Administration, Definitions, General Regulations, Ventilation, Exhaust Systems, Duct Systems, Combustion Air, Chimneys & Vents and Specific Appliances. |
|
MONTANA |
|
2006 UPC with Montana Amendments
Length: 4 hours
Description: Specific for the State of Montana and renewal of state plumbing license. Seminar is based on the 2006 UPC and the Montana amendments and plumbing licensure. Topics covered include: Administration, Definitions, General Regulations, Fixtures, Water Heaters, Water Supply and Sizing, Drainage, Indirect Wastes, Vents, Traps, Storm Drainage and Fire Stopping. |
|
TEXAS |
|
2003 UPC with Austin Amendments
Length: 1 day
Description: Specific for Austin, Texas, this comprehensive course, based on the 2003 Uniform Plumbing provides a complete overview of the Austin requirements including: Water System Sizing, Drain, Waste and Vent System Design, Gas System Design and Sizing, Cross Connection, Materials, Water Heater Installation, Venting, Combustion Air Requirements and Fixtures. |
|
2003 UPC with Houston Amendments
Length: 1 day
Description: Specific for Houston, Texas, this comprehensive overview provides a clear understanding of the 2003 Uniform Plumbing Code with Houston Amendments. Topics include: General Administration, Water System Sizing, Drain, Waste and Vent System Design, Gas System Design and Sizing, Cross Connection, Materials, Water Heater Installation, Venting, Combustion Air Requirements and Fixtures. |
|
2003 UMC with Houston Amendments
Length: 1 day
Description: Specific for Houston, Texas, this comprehensive overview provides a clear understanding of the 2003 Uniform Mechanical Code with Houston Amendments. Topics include: General Administration, Equipment Installation, Access, Venting, Clearances, and Combustion Air, Kitchen Hoods, Fuel Gas Systems, Ducts, Refrigeration, Boilers, Administration, Hydronics, Dryer Exhaust and the Houston specific requirements as well. |
|
WASHINGTON |
|
2006 UPC with Washington Amendments
Length: 1 day
Description: Specific for the State of Washington, this seminar is based on the 2003 Uniform Plumbing Code including the Washington amendments. A full comprehensive understanding of the Washington requirements, this seminar covers: General Administration; Water System Sizing, Drain, Waste and Vent System Design, Gas System Design and Sizing, Cross Connection, Materials, Water Heater Installation, Venting, Combustion Air Requirements and Fixtures |
|